この記事は２年以上前に書いたものです。
そのため情報が古い可能性があります。ご了承ください。m(_ _)m
そのため情報が古い可能性があります。ご了承ください。m(_ _)m
smart-ups 700からアラーム音が鳴り、要バッテリ交換LEDが赤く点灯していた。
(Smart-UPSの警告音(アラーム音)の種類、Smart-UPSの前面パネルのLED概要)
また、apcupsdから次のようなメールがちょくちょく来てた。
Subject: qos UPS battery needs changing NOW.
qos UPS battery needs changing NOW.
APC : 001,053,1336
DATE : 2010-11-06 19:19:08 +0900
HOSTNAME : qos
VERSION : 3.14.8 (16 January 2010) debian
UPSNAME : UPS_IDEN
CABLE : Custom Cable Smart
MODEL : SMART-UPS 700
UPSMODE : Stand Alone
STARTTIME: 2010-09-10 02:41:15 +0900
STATUS : ONLINE REPLACEBATT
LINEV : 100.7 Volts
LOADPCT : 58.7 Percent Load Capacity
BCHARGE : 099.0 Percent
TIMELEFT : 18.0 Minutes
MBATTCHG : 5 Percent
MINTIMEL : 3 Minutes
MAXTIME : 0 Seconds
MAXLINEV : 101.4 Volts
MINLINEV : 099.4 Volts
OUTPUTV : 100.7 Volts
SENSE : High
DWAKE : 000 Seconds
DSHUTD : 180 Seconds
DLOWBATT : 05 Minutes
LOTRANS : 090.0 Volts
HITRANS : 110.0 Volts
RETPCT : 000.0 Percent
ITEMP : 49.0 C Internal
ALARMDEL : 5 seconds
BATTV : 27.2 Volts
LINEFREQ : 50.0 Hz
LASTXFER : Automatic or explicit self test
NUMXFERS : 2
XONBATT : 2010-11-03 19:59:30 +0900
TONBATT : 0 seconds
CUMONBATT: 5 seconds
XOFFBATT : 2010-11-03 19:59:35 +0900
LASTSTEST: 2010-11-03 19:59:30 +0900
SELFTEST : NO
STESTI : 336
STATFLAG : 0x07000088 Status Flag
DIPSW : 0x00 Dip Switch
REG1 : 0x00 Register 1
REG2 : 0x00 Register 2
REG3 : 0x00 Register 3
MANDATE : 12/19/01
SERIALNO : XXXXXXXXXXXX
BATTDATE : 12/19/01
NOMOUTV : 100 Volts
NOMBATTV : 24.0 Volts
EXTBATTS : 0
FIRMWARE : 50.14S.A
APCMODEL : GWA
END APC : 2010-11-06 19:19:10 +0900
qos UPS battery needs changing NOW.
APC : 001,053,1336
DATE : 2010-11-06 19:19:08 +0900
HOSTNAME : qos
VERSION : 3.14.8 (16 January 2010) debian
UPSNAME : UPS_IDEN
CABLE : Custom Cable Smart
MODEL : SMART-UPS 700
UPSMODE : Stand Alone
STARTTIME: 2010-09-10 02:41:15 +0900
STATUS : ONLINE REPLACEBATT
LINEV : 100.7 Volts
LOADPCT : 58.7 Percent Load Capacity
BCHARGE : 099.0 Percent
TIMELEFT : 18.0 Minutes
MBATTCHG : 5 Percent
MINTIMEL : 3 Minutes
MAXTIME : 0 Seconds
MAXLINEV : 101.4 Volts
MINLINEV : 099.4 Volts
OUTPUTV : 100.7 Volts
SENSE : High
DWAKE : 000 Seconds
DSHUTD : 180 Seconds
DLOWBATT : 05 Minutes
LOTRANS : 090.0 Volts
HITRANS : 110.0 Volts
RETPCT : 000.0 Percent
ITEMP : 49.0 C Internal
ALARMDEL : 5 seconds
BATTV : 27.2 Volts
LINEFREQ : 50.0 Hz
LASTXFER : Automatic or explicit self test
NUMXFERS : 2
XONBATT : 2010-11-03 19:59:30 +0900
TONBATT : 0 seconds
CUMONBATT: 5 seconds
XOFFBATT : 2010-11-03 19:59:35 +0900
LASTSTEST: 2010-11-03 19:59:30 +0900
SELFTEST : NO
STESTI : 336
STATFLAG : 0x07000088 Status Flag
DIPSW : 0x00 Dip Switch
REG1 : 0x00 Register 1
REG2 : 0x00 Register 2
REG3 : 0x00 Register 3
MANDATE : 12/19/01
SERIALNO : XXXXXXXXXXXX
BATTDATE : 12/19/01
NOMOUTV : 100 Volts
NOMBATTV : 24.0 Volts
EXTBATTS : 0
FIRMWARE : 50.14S.A
APCMODEL : GWA
END APC : 2010-11-06 19:19:10 +0900
「Smart-UPS 700のバッテリーが切れた」で、バッテリーをPXL12072に変更してから1年と11ヶ月くらいしか経ってないのに。。
アラームがうるさかったので、また互換バッテリーを購入することに。今度は、完全密封型鉛蓄電池（１２Ｖ８Ａｈ）ＷＰ８－１２を、\2,450 X 2 + \500(送料) + \300(代引き手数料) = \5,700 で。
注文してから2日後に届く。
Smart-ups 700 は赤ランプ点灯中。
フロントパネルを外す。
バッテリーの下に挟まってる紙は、バッテリーを取り出しやすくするため。
どこかのサイトに書いてたってそれを真似した。
PXL12072。
WP8-12に、両面テープを貼って、ケーブルを接続。
バッテリーが入っていない状態のSmart-UPS 700
WP8-12を取り付ける。
TESTボタンを長押ししてセルフテストを動作させると・・・。
要バッテリー交換LEDが消えた！！
フロントパネルを取り付ける。
バッテリー交換した日付を更新。
前回忘れてたけど、今回は「jlb APC SU700J のバッテリィ交換」を参考に実施。
% sudo apctest
2010-11-11 01:36:41 apctest 3.14.8 (16 January 2010) debian
Checking configuration ...
Attached to driver: apcsmart
sharenet.type = DISABLE
cable.type = CUSTOM_SMART
You are using a SMART cable type, so I'm entering SMART test mode
mode.type = APCSMART_UPS
Setting up the port ...
apctest FATAL ERROR in device.c at line 71
Unable to create UPS lock file.
If apcupsd or apctest is already running,
please stop it and run this program again.
apctest error termination completed
2010-11-11 01:36:41 apctest 3.14.8 (16 January 2010) debian
Checking configuration ...
Attached to driver: apcsmart
sharenet.type = DISABLE
cable.type = CUSTOM_SMART
You are using a SMART cable type, so I'm entering SMART test mode
mode.type = APCSMART_UPS
Setting up the port ...
apctest FATAL ERROR in device.c at line 71
Unable to create UPS lock file.
If apcupsd or apctest is already running,
please stop it and run this program again.
apctest error termination completed
早速apcupsdを止めろと怒られる。
% sudo /etc/init.d/apcupsd stop
Stopping UPS power management: apcupsd.
% sudo apctest
2010-11-11 01:37:22 apctest 3.14.8 (16 January 2010) debian
Checking configuration ...
Attached to driver: apcsmart
sharenet.type = DISABLE
cable.type = CUSTOM_SMART
You are using a SMART cable type, so I'm entering SMART test mode
mode.type = APCSMART_UPS
Setting up the port ...
Hello, this is the apcupsd Cable Test program.
This part of apctest is for testing Smart UPSes.
Please select the function you want to perform.
1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
Q) Quit
Select function number: 5
This is the EEPROM programming section of apctest.
Please select the function you want to perform.
1) Print EEPROM values
2) Change Battery date
3) Change UPS name
4) Change sensitivity
5) Change alarm delay
6) Change low battery warning delay
7) Change wakeup delay
8) Change shutdown delay
9) Change low transfer voltage
10) Change high transfer voltage
11) Change battery return threshold percent
12) Change output voltage when on batteries
13) Change the self test interval
14) Set EEPROM with conf file values
Q) Quit
Select function number: 2
Enter new battery date -- DD/MM/YY: 11/11/10
Attempting to update UPS battery date ...
The old UPS battery date is: 12/19/01
The new UPS battery date is: 11/11/10
1) Print EEPROM values
2) Change Battery date
3) Change UPS name
4) Change sensitivity
5) Change alarm delay
6) Change low battery warning delay
7) Change wakeup delay
8) Change shutdown delay
9) Change low transfer voltage
10) Change high transfer voltage
11) Change battery return threshold percent
12) Change output voltage when on batteries
13) Change the self test interval
14) Set EEPROM with conf file values
Q) Quit
Select function number: Q
2010-11-11 01:38:31 End EEPROM programming.
1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
Q) Quit
Select function number: Q
2010-11-11 01:38:34 End apctest.
% sudo /etc/init.d/apcupsd start
Starting UPS power management: apcupsd.
Stopping UPS power management: apcupsd.
% sudo apctest
2010-11-11 01:37:22 apctest 3.14.8 (16 January 2010) debian
Checking configuration ...
Attached to driver: apcsmart
sharenet.type = DISABLE
cable.type = CUSTOM_SMART
You are using a SMART cable type, so I'm entering SMART test mode
mode.type = APCSMART_UPS
Setting up the port ...
Hello, this is the apcupsd Cable Test program.
This part of apctest is for testing Smart UPSes.
Please select the function you want to perform.
1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
Q) Quit
Select function number: 5
This is the EEPROM programming section of apctest.
Please select the function you want to perform.
1) Print EEPROM values
2) Change Battery date
3) Change UPS name
4) Change sensitivity
5) Change alarm delay
6) Change low battery warning delay
7) Change wakeup delay
8) Change shutdown delay
9) Change low transfer voltage
10) Change high transfer voltage
11) Change battery return threshold percent
12) Change output voltage when on batteries
13) Change the self test interval
14) Set EEPROM with conf file values
Q) Quit
Select function number: 2
Enter new battery date -- DD/MM/YY: 11/11/10
Attempting to update UPS battery date ...
The old UPS battery date is: 12/19/01
The new UPS battery date is: 11/11/10
1) Print EEPROM values
2) Change Battery date
3) Change UPS name
4) Change sensitivity
5) Change alarm delay
6) Change low battery warning delay
7) Change wakeup delay
8) Change shutdown delay
9) Change low transfer voltage
10) Change high transfer voltage
11) Change battery return threshold percent
12) Change output voltage when on batteries
13) Change the self test interval
14) Set EEPROM with conf file values
Q) Quit
Select function number: Q
2010-11-11 01:38:31 End EEPROM programming.
1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
Q) Quit
Select function number: Q
2010-11-11 01:38:34 End apctest.
% sudo /etc/init.d/apcupsd start
Starting UPS power management: apcupsd.
Smart-UPS 700から情報取得。
% sudo apcaccess status
APC : 001,051,1222
DATE : 2010-11-11 01:57:30 +0900
HOSTNAME : qos
VERSION : 3.14.8 (16 January 2010) debian
UPSNAME : UPS_IDEN
CABLE : Custom Cable Smart
MODEL : SMART-UPS 700
UPSMODE : Stand Alone
STARTTIME: 2010-11-11 01:38:43 +0900
STATUS : ONLINE
LINEV : 100.7 Volts
LOADPCT : 57.2 Percent Load Capacity
BCHARGE : 099.0 Percent
TIMELEFT : 18.0 Minutes
MBATTCHG : 5 Percent
MINTIMEL : 3 Minutes
MAXTIME : 0 Seconds
MAXLINEV : 101.4 Volts
MINLINEV : 099.4 Volts
OUTPUTV : 101.4 Volts
SENSE : High
DWAKE : 000 Seconds
DSHUTD : 180 Seconds
DLOWBATT : 05 Minutes
LOTRANS : 090.0 Volts
HITRANS : 110.0 Volts
RETPCT : 000.0 Percent
ITEMP : 46.8 C Internal
ALARMDEL : 5 seconds
BATTV : 27.2 Volts
LINEFREQ : 50.0 Hz
LASTXFER : Automatic or explicit self test
NUMXFERS : 0
TONBATT : 0 seconds
CUMONBATT: 0 seconds
XOFFBATT : N/A
SELFTEST : NO
STESTI : 336
STATFLAG : 0x07000008 Status Flag
DIPSW : 0x00 Dip Switch
REG1 : 0x00 Register 1
REG2 : 0x00 Register 2
REG3 : 0x00 Register 3
MANDATE : 12/19/01
SERIALNO : XXXXXXXXXXXX
BATTDATE : 11/11/10
NOMOUTV : 100 Volts
NOMBATTV : 24.0 Volts
EXTBATTS : 0
FIRMWARE : 50.14S.A
APCMODEL : GWA
END APC : 2010-11-11 01:58:07 +0900
APC : 001,051,1222
DATE : 2010-11-11 01:57:30 +0900
HOSTNAME : qos
VERSION : 3.14.8 (16 January 2010) debian
UPSNAME : UPS_IDEN
CABLE : Custom Cable Smart
MODEL : SMART-UPS 700
UPSMODE : Stand Alone
STARTTIME: 2010-11-11 01:38:43 +0900
STATUS : ONLINE
LINEV : 100.7 Volts
LOADPCT : 57.2 Percent Load Capacity
BCHARGE : 099.0 Percent
TIMELEFT : 18.0 Minutes
MBATTCHG : 5 Percent
MINTIMEL : 3 Minutes
MAXTIME : 0 Seconds
MAXLINEV : 101.4 Volts
MINLINEV : 099.4 Volts
OUTPUTV : 101.4 Volts
SENSE : High
DWAKE : 000 Seconds
DSHUTD : 180 Seconds
DLOWBATT : 05 Minutes
LOTRANS : 090.0 Volts
HITRANS : 110.0 Volts
RETPCT : 000.0 Percent
ITEMP : 46.8 C Internal
ALARMDEL : 5 seconds
BATTV : 27.2 Volts
LINEFREQ : 50.0 Hz
LASTXFER : Automatic or explicit self test
NUMXFERS : 0
TONBATT : 0 seconds
CUMONBATT: 0 seconds
XOFFBATT : N/A
SELFTEST : NO
STESTI : 336
STATFLAG : 0x07000008 Status Flag
DIPSW : 0x00 Dip Switch
REG1 : 0x00 Register 1
REG2 : 0x00 Register 2
REG3 : 0x00 Register 3
MANDATE : 12/19/01
SERIALNO : XXXXXXXXXXXX
BATTDATE : 11/11/10
NOMOUTV : 100 Volts
NOMBATTV : 24.0 Volts
EXTBATTS : 0
FIRMWARE : 50.14S.A
APCMODEL : GWA
END APC : 2010-11-11 01:58:07 +0900
BATTDATEが更新されてる。
それにしても、ITEMPが高ぇ。。常夏か？